View MPC953_244577.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Product Preview
Low Voltage PLL Clock Driver
The MPC953 is a 3.3V compatible, PLL based clock driver device targeted for high performance clock tree designs. With output frequencies of up to 87.5MHz and output skews of 150ps the MPC953 is ideal for the most demanding clock tree designs. The devices employ a fully differential PLL design to minimize cycle-to-cycle and phase jitter.
MPC953
* * * * *
Fully Integrated PLL Output Frequency up to 87.5MHz Outputs Disable in High Impedance TQFP Packaging 100ps Cycle-to-Cycle Jitter
LOW VOLTAGE PLL CLOCK DRIVER
The MPC953 has a differential LVPECL reference input along with an external feedback input. These features make the MPC953 ideal for use as a zero delay, low skew fanout buffer. The device performance has been tuned and optimized for zero delay performance. The MR/OE input pin will reset the internal counters and tristate the output buffers when driven "high". If the reference clock (PECL_CLK) is lost or shut down when the MPC953 is in phase-lock, the output frquency will slew slowly downward. The final VCO frequency will be around TBDMHz. The MPC953 is fully 3.3V compatible and requires no external loop filter components. All control inputs accept LVCMOS or LVTTL compatible levels while the outputs provide LVCMOS levels with the ability to drive terminated 50 transmission lines. For series terminated 50 lines, each of the MPC953 outputs can drive two traces giving the device an effective fanout of 1:18. The device is packaged in a 7x7mm 32-lead TQFP package to provide the optimum combination of board density and performance.
FA SUFFIX 32-LEAD TQFP PACKAGE CASE 873A-02
QFB PECL_CLK PECL_CLK FB_CLK VCO_SEL BYPASS MR/OE 7 Phase Detector LPF VCO 200-350MHz /4 /2 Q7
Q0:6
Figure 1. Logic Diagram
This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice. 9/97
(c) Motorola, Inc. 1997
1
REV 0.1
MPC953
GNDO GNDO 17 16 15 14 13 Q5 VCCO VCCO 19
Q1
Q2
Q3
24 GNDO Q0 VCCO QFB GNDO NC BYPASS VCO_SEL 25 26 27 28
23
22
21
20
Q4 18
FUNCTION TABLES
VCCO BYPASS Q6 GNDO Q7 VCCO MR/OE PECL_CLK 1 0 MR/OE 1 0 VCO_SEL 1 0 Function PLL Enabled PLL Bypass Function Outputs Disabled Outputs Enabled Function /2 /1
MPC953
29 30 31 32 1 2 3 4 5 6 7 8 12 11 10 9
Figure 2. 32-Lead Pinout (Top View)
ABSOLUTE MAXIMUM RATINGS*
Symbol VCC VI IIN TStor Supply Voltage Input Voltage Input Current Storage Temperature Range -40 Parameter Min -0.3 -0.3 Max 4.6 VDD + 0.3 20 125 Unit V V mA C
* Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute-maximum-rated conditions is not implied.
MOTOROLA
PECL_CLK
VCCA
FB_CLK
GNDI
NC
NC
NC
NC
2
ECLinPS and ECLinPS Lite DL140 -- Rev 3
MPC953
DC CHARACTERISTICS (TA = 0 to 70C, VCC = 3.3V 5%)
Symbol VIH VIL VPP VCMR VOH VOL IIN CIN Cpd ICC Characteristic Input HIGH Voltage LVCMOS Inputs Input LOW Voltage LVCMOS Inputs Peak-to-Peak Input Voltage PECL_CLK Common Mode Range Output HIGH Voltage Output LOW Voltage Input Current Input Capacitance Power Dissipation Capacitance Maximum Quiescent Supply Current 25 75 PECL_CLK 300 VCC-1.5 2.4 0.5 120 4 Min 2.0 Typ Max 3.6 0.8 1000 VCC-0.6 Unit V V mV mV V V A pF pF mA Per Output All VCC Pins Note 1. IOH = -40mA, Note 2. IOL = 40mA, Note 2. Condition
ICCPLL Maximum PLL Supply Current 15 20 mA VCCA Pin Only 1. VCMR is the difference from the most positive side of the differential input signal. Normal operation is obtained when the "HIGH" input is within the VCMR range and the input swing lies within the VPP specification. 2. The MPC953 outputs can drive series or parallel terminated 50 (or 50 to VCC/2) transmission lines on the incident edge (see Applications Info section).
PLL INPUT REFERENCE CHARACTERISTICS (TA = 0 to 70C)
Symbol fref Characteristic Reference Input Frequency Min Note 3. Max Note 3. Unit MHz % Condition
frefDC Reference Input Duty Cycle 25 75 3. Maximum and minimum input reference is limited by the VCO lock range and the feedback divider.
AC CHARACTERISTICS (TA = 0C to 70C, VCC = 3.3V 5%)
Symbol tr, tf tpw tsk(O) fVCO fmax tpd(lock) tpd(bypass) tPLZ,HZ tPZL tjitter Characteristic Output Rise/Fall Time Output Duty Cycle Output-to-Output Skews (Relative to QFB) PLL VCO Lock Range Maximum Output Frequency Input to Ext_FB Delay (with PLL Locked) Input to Q Delay (with PLL Bypassed) Output Disable Time Output Enable Time Cycle-to-Cycle Jitter (Peak-to-Peak) 200 50 X-100 5 X (Note 4.) Min 0.10 45 50 Typ Max 1.0 55 75 350 87.5 X+100 10 7 6 100 10 Unit ns % ps MHz MHz ps ns ns ns ps ms VCO_SEL = `0' fref = 75MHz Condition 0.8 to 2.0V
tlock Maximum PLL Lock Time 4. X will be targeted for 0ns, but may vary from target by 150ps based on characterization of silicon.
ECLinPS and ECLinPS Lite DL140 -- Rev 3
3
MOTOROLA
MPC953
Power Supply Filtering The MPC953 is a mixed analog/digital product and as such it exhibits some sensitivities that would not necessarily be seen on a fully digital product. Analog circuitry is naturally susceptible to random noise, especially if this noise is seen on the power supply pins. The MPC953 provides separate power supplies for the output buffers (VCCO) and the phase-locked loop (VCCA) of the device. The purpose of this design technique is to try and isolate the high switching noise digital outputs from the relatively sensitive internal analog phase-locked loop. In a controlled environment such as an evaluation board this level of isolation is sufficient. However, in a digital system environment where it is more difficult to minimize noise on the power supplies a second level of isolation may be required. The simplest form of isolation is a power supply filter on the VCCA pin for the MPC953. Figure 3 illustrates a typical power supply filter scheme. The MPC953 is most susceptible to noise with spectral content in the 1KHz to 1MHz range. Therefore the filter should be designed to target this range. The key parameter that needs to be met in the final filter design is the DC voltage drop that will be seen between the VCC supply and the VCCA pin of the MPC953. From the data sheet the IVCCA current (the current sourced through the VCCA pin) is typically 15mA (20mA maximum), assuming that a minimum of 3.0V must be maintained on the VCCA pin very little DC voltage drop can be tolerated when a 3.3V VCC supply is used. The resistor shown in Figure 3 must have a resistance of 10-15 to meet the voltage drop criteria. The RC filter pictured will provide a broadband filter with approximately 100:1 attenuation for noise whose spectral content is above 20KHz. As the noise frequency crosses the series resonant point of an individual capacitor it's overall impedance begins to look inductive and thus increases with increasing frequency. The parallel capacitor combination shown ensures that a low impedance path to ground exists for frequencies well above the bandwidth of the PLL. It is recommended that the user start with an 8-10 resistor to avoid potential VCC drop problems and only move to the higher value resistors when a higher level of attenuation is shown to be needed. be applications in which overall performance is being degraded due to system power supply noise. The power supply filter schemes discussed in this section should be adequate to eliminate power supply noise related problems in most designs. Driving Transmission Lines The MPC953 clock driver was designed to drive high speed signals in a terminated transmission line environment. To provide the optimum flexibility to the user the output drivers were designed to exhibit the lowest impedance possible. With an output impedance of less than 10 the drivers can drive either parallel or series terminated transmission lines. For more information on transmission lines the reader is referred to application note AN1091 in the Timing Solutions brochure (BR1333/D). In most high performance clock networks point-to-point distribution of signals is the method of choice. In a point-to-point scheme either series terminated or parallel terminated transmission lines can be used. The parallel technique terminates the signal at the end of the line with a 50 resistance to VCC/2. This technique draws a fairly high level of DC current and thus only a single terminated line can be driven by each output of the MPC953 clock driver. For the series terminated case however there is no DC current draw, thus the outputs can drive multiple series terminated lines. Figure 4 illustrates an output driving a single series terminated line vs two series terminated lines in parallel. When taken to its extreme the fanout of the MPC953 clock driver is effectively doubled due to its capability to drive multiple lines.
MPC953 OUTPUT BUFFER IN 7 RS = 43 ZO = 50 OutA
MPC953 OUTPUT BUFFER IN 7
RS = 43
ZO = 50 OutB0
3.3V ZO = 50
RS=5-15 PLL_VCC 22F MPC953 VCC 0.01F 0.01F
RS = 43
OutB1
Figure 4. Single versus Dual Transmission Lines The waveform plots of Figure 5 show the simulation results of an output driving a single line vs two lines. In both cases the drive capability of the MPC953 output buffers is more than sufficient to drive 50 transmission lines on the incident edge. Note from the delay measurements in the simulations a delta of only 43ps exists between the two differently loaded outputs. This suggests that the dual line driving need not be used exclusively to maintain the tight output-to-output skew of the MPC953. The output waveform in Figure 5 shows a step in the waveform, this step is caused
Figure 3. Power Supply Filter Although the MPC953 has several design features to minimize the susceptibility to power supply noise (isolated power and grounds and fully differential PLL) there still may
MOTOROLA
4
ECLinPS and ECLinPS Lite DL140 -- Rev 3
MPC953
by the impedance mismatch seen looking into the driver. The parallel combination of the 43 series resistor plus the output impedance does not match the parallel combination of the line impedances. The voltage wave launched down the two lines will equal: VL = VS ( Zo / (Rs + Ro +Zo)) Zo = 50 || 50 Rs = 43 || 43 Ro = 7 VL = 3.0 (25 / (21.5 + 7 + 25) = 3.0 (25 / 53.5) = 1.40V At the load end the voltage will double, due to the near unity reflection coefficient, to 2.8V. It will then increment towards the quiescent 3.0V in steps separated by one round trip delay (in this case 4.0ns).
3.0 OutA tD = 3.8956 OutB tD = 3.9386
Since this step is well above the threshold region it will not cause any false clock triggering, however designers may be uncomfortable with unwanted reflections on the line. To better match the impedances when driving multiple lines the situation in Figure 6 should be used. In this case the series terminating resistors are reduced such that when the parallel combination is added to the output buffer impedance the line impedance is perfectly matched.
MPC953 OUTPUT BUFFER 7 RS = 36 ZO = 50
RS = 36
ZO = 50
2.5
7 + 36 k 36 = 50 k 50 25 = 25 Figure 6. Optimized Dual Line Termination
VOLTAGE (V)
2.0 In 1.5
1.0
SPICE level output buffer models are available for engineers who want to simulate their specific interconnect schemes. In addition IV characteristics are in the process of being generated to support the other board level simulators in general use.
0.5
0 2 4 6 8 TIME (nS) 10 12 14
Figure 5. Single versus Dual Waveforms
ECLinPS and ECLinPS Lite DL140 -- Rev 3
5
MOTOROLA
MPC953
OUTLINE DIMENSIONS
FA SUFFIX TQFP PACKAGE CASE 873A-02 ISSUE A
A A1
32 25 4X
0.20 (0.008) AB T-U Z
1
-T- B B1
8
-U- V P DETAIL Y
17
AE
V1 AE DETAIL Y
9
-Z- 9 S1 S
4X
0.20 (0.008) AC T-U Z
G -AB-
SEATING PLANE
DETAIL AD
-AC-
BASE METAL
F
8X
M_ R
CE
SECTION AE-AE
X DETAIL AD
MOTOROLA
GAUGE PLANE
0.250 (0.010)
H
W
K
Q_
EE EE EE EE
N
D
0.20 (0.008)
M
AC T-U Z
0.10 (0.004) AC
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE -AB- IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DATUMS -T-, -U-, AND -Z- TO BE DETERMINED AT DATUM PLANE -AB-. 5. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE -AC-. 6. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.250 (0.010) PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE -AB-. 7. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. DAMBAR PROTRUSION SHALL NOT CAUSE THE D DIMENSION TO EXCEED 0.520 (0.020). 8. MINIMUM SOLDER PLATE THICKNESS SHALL BE 0.0076 (0.0003). 9. EXACT SHAPE OF EACH CORNER MAY VARY FROM DEPICTION. MILLIMETERS MIN MAX 7.000 BSC 3.500 BSC 7.000 BSC 3.500 BSC 1.400 1.600 0.300 0.450 1.350 1.450 0.300 0.400 0.800 BSC 0.050 0.150 0.090 0.200 0.500 0.700 12_ REF 0.090 0.160 0.400 BSC 1_ 5_ 0.150 0.250 9.000 BSC 4.500 BSC 9.000 BSC 4.500 BSC 0.200 REF 1.000 REF INCHES MIN MAX 0.276 BSC 0.138 BSC 0.276 BSC 0.138 BSC 0.055 0.063 0.012 0.018 0.053 0.057 0.012 0.016 0.031 BSC 0.002 0.006 0.004 0.008 0.020 0.028 12_ REF 0.004 0.006 0.016 BSC 1_ 5_ 0.006 0.010 0.354 BSC 0.177 BSC 0.354 BSC 0.177 BSC 0.008 REF 0.039 REF
J
DIM A A1 B B1 C D E F G H J K M N P Q R S S1 V V1 W X
6
ECLinPS and ECLinPS Lite DL140 -- Rev 3
-T-, -U-, -Z-
MPC953
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or 1-800-441-2447 Customer Focus Center: 1-800-521-6274 MfaxTM: RMFAX0@email.sps.mot.com - TOUCHTONE 1-602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, Motorola Fax Back System - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 - http://sps.motorola.com/mfax/ HOME PAGE: http://motorola.com/sps/ JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. 81-3-5487-8488
ECLinPS and ECLinPS Lite DL140 -- Rev 3 7
MPC953/D MOTOROLA

▲Up To Search▲

Price & Availability of MPC953

	To Download MPC953 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .